by Todd Walker
I’m not one to ask for help often. But I’m glad I did. They kept showing up in the Georgia heat and humidity ready to sweat through 90+ degree temperatures.
The Crew disassembled the log cabin in one day at the end of June. Once the logs were moved to the new site, I started putting the puzzle back together. I managed to stack 7 courses on the sill logs before The Crew reached out and scolded me for not extending an invitation sooner. “All ya gotta do is ask.” I’m still amazed, but shouldn’t be, that they keep coming to this party. True friends do that, ya know.
Now we’re to the point of needing metal for the roof. Here’s a look at the progress since my last log cabin update (July 31, 2019).
Stacking Wall Logs
Re-assembling the wall logs was like a paint by numbers set. Dianne had labeled the logs before we took it down. It was just a matter of putting numbers back where we found them on the walls.
Setting the Ridge Pole
I dreaded this task. I wasn’t sure if the plan would work. How could we get a 21 foot log over thirteen feet above the floor, balanced and secured atop two vertical ridge pole support logs?
Turns out that raising the ridge pole (RP) may have been the easiest part of the build. We cut and peeled two ridge pole support logs (RPSL) and attached them to the back and porch walls with 1/2″ all-thread rod. The poles reached about 5 feet above the plate logs to give me the pitch I wanted for the roof.
We attached 2×6’s to the top of each RPSL as temporary lifting poles. A 2×6 spacer board was screwed between the RP and the temporary lifting pole. This would give the space needed for the RP to rest on the center of the RPSL’s when lifted in place. Two chain falls were secured to the 2×6 lifting poles before the RPSL’s were lifted into place.
We predrilled holes for the rebar pins in the RP before lifting. With rigging in place, we slowly lifted the RP to the top of the RPSL’s. This went smoother than I could have imagined. JT aligned his end and drove a rebar pin through the RP into the RPSL with 3 inches of rebar above the RP. The 3 inches of rebar was bent over on top of the RP for added holding power.
Even though we measured hole placement on the RP, my end was 4 inches short of center on the RPSL. I re-drilled my end from the scaffolding we built. I drove in my rebar to secure the RP. Time for much needed break!
I had originally planned to use log rafters and log gables on this project. However, with all the delays we encountered with the disassembly and reassembly, I opted for dimensional lumber to expedite the process. This is just a practice cabin, by the way.
We sank a deck screw in two of the 2″x6″x14′ laid out at a 45 degree angle. The screw allowed the boards to “scissor” on top of the RP as we rested the tails on the top plate logs.
We slid the rafters down the RP and set them on 2 foot centers. We eyeballed the first rafter’s placement on the plate logs and toe-nailed it into place. I probably should have sawn the RP and plate logs flat to get a level run on the rafters. To correct the situation, we’ll have to lift or lower individual rafters at the top plate logs as needed. There’s always challenges when using dimensional lumber on raw logs.
The gables, as mentioned earlier, will be dimensional lumber. I’m not sure what I’ll use for sheathing the gables. A few ideas are floating in my head.
A top plate log needed to be installed between the long porch plate logs. We skinned a log, measured and cut to length, and pinned it. We used two of the original ax-hewn floor joists from the first build to vertically support the cross member.
We laid two rafter boards flat over the RP to create a top plate for the gable studs. We started framing under the RP and worked our way out to the plate logs with 2×6 studs. Dianne did a fine job of cutting bevels and lengths for the studs.
The sleeping loft will be above the porch where The Crew is standing. Like most of the plans on this project, we’ll figure it out as we go.
Keep Doing the Stuff of Self-Reliance,
P.P.S – If you find value in our blog, Dirt Road Girl and I would appreciate your vote on Top Prepper Sites! You can vote daily by clicking here or on the image below. Check out all the other value-adding sites while you’re there…
Thanks for Sharing the Stuff!
Copyright © by Survival Sherpa: Content on this site (unless the work of a third-party) may be shared freely in digital form, in part or whole, for non-commercial use with a link back to this site crediting the author. All links in articles must remain intact as originally posted in order to be republished. If you are interested a third-party article, please contact the author directly for republishing information.